Yes, the Advent Air RV Air Conditioner # ACM135B will replace your Coleman Mach air conditioner on your 2018 Heartland Pioneer BH270 travel trailer. The Advent will allow you to retain and use your Coleman thermostat and air distribution box by using the Coleman Mach Adapter Wiring Kit # ACCOLKIT.
We also have the Furrion Chill Replacement RV Air Conditioner for Coleman Setup # FR42PV if you want the higher 15,000 BTU cooling capacity. The Advent is only a 13,500 BTU air conditioner.... view full answer...
There are no replacement hoses for the RV Kitchen Faucet w/ Pull Down Spout # 277-000129; if your hose was damaged and irreparable you will need to replace your entire faucet; while that is understandably not the news you wanted to hear, these faucets do need to be replaced if the hoses are damaged. view full answer...
Your brakes shouldn't necessarily lock up at max boost output. The goal is not to lock the tires and cause the trailer tires to skid but rather to give strong breaking pressure to bring to a safe stop. It sounds like you have your brake assemblies # AKEBRK-35R-SA adjusted properly.
You should just have a slight drag on your hub when you rotate your trailer wheel when it is off the ground. You shouldn't have too much drag or you will simply wear down your brake shoes prematurely. view full answer...
I went ahead and checked out what we have for your 2018 Heartland RV Pioneer Travel Trailer, and the closest I was able to find is the:
-Low Profile LED RV Tail Light - Stop, Tail, Turn - 9 Diodes # RVSTLB60 for the passenger side, & the,
-Low Profile LED RV Tail Light w/ License Bracket # RVSTLB61 for the driver side.
These lights measure 8-11/16" long and 3-3/16" wide. view full answer...
The SaltDogg Electric Hitch-Mount Salt Spreader part # 337TGSUV1B won't work with sand but we do have an option that will work with a salt/sand mix, the SaltDogg Electric Tailgate Salt Spreader part # 337TGS07 but it does however require a pickup. view full answer...
The Vesper Steel Modular Trailer Wheel you'd looked at, part # MX59FR has a zero offset, but we do have something that will work for you.
For a similar modular trailer wheel in silver with a +0.5 offset, use the Dexstar steel mod wheel, part # AM20797. The wheel has an 8 on 6-1/2 inch bolt pattern and a 3750 lb per wheel capacity.
If you click the provided video link, my buddy Jeff will run you through the features of the wheel. view full answer...
I took a look at what we have for the Westin Molded, Lighted Running Boards # 27-0015, and the Replacement Lenses and Housings for Westin Molded, Lighted Running Boards # 27-9904 actually comes with a rubber seal pre-installed so there is not a rubber grommet for this.
If you also need replacement bulbs, you can use the Replacement Bulbs for Westin Molded, Lighted Step Boards # 27-9905.
If you're referring to something different, let me know and I'd be happy to see what we have. view full answer...
The seat height of the Dometic # DOM87FR Full-Timer RV toilet is 18-1/4 inches. I've provided a diagram with all the dimensions for reference. view full answer...
When installing a ladder on your 2018 Heartland RV the key is making sure the new ladder mounts to the RV's structural components under its outer skin. It is possible that the screw holes will not line up exactly but so long as they allow the included fasteners to reach those structural components the ladder will be able to safely support its maximum rated weight load of 275-lbs for the Surco Ladder part # SP502L.
As far as mounting a portable waste tank on the roof I can't say I've had... view full answer...
To completely cut power to the 10 Cu Ft Everchill Refrigerator for RVs # 324-000119 you need to either disconnect the power wires at the back, or you should have a breaker in your camper that the fridge is on. If you flip that breaker then it will cut power to the fridge without disconnecting any wires. view full answer...
The correct replacement for the Dexter Trailer Hub and Drum Assembly 008-247-05 is the Dexter Trailer Hub and Drum Assembly part # 84546UC3 or if you're looking for a more cost effective replacement, the Trailer Hub and Drum Assembly part # AKHD-545-35-K. view full answer...
If an RV toilet is emitting a bad smell that just means the gaskets are failing. You can replace the gasket between the floor and toilet with part # Q23653VP and the flush gasket that holds water in the bowl and prevents odors with part # DOM63FR.
Most toilets require 11" of clearance from the center of the drain back to the wall, except for the 300 series which only requires 8.5". Since you don't have the extra space you would need to stick with a 300 series with either the White # DOM64FR... view full answer...
The most amount of drop we offer in a weight distribution shank with 2-1/2" stinger is 9-1/4", the Curt Weight Distribution Shank part # C17132 which can be used with an Equal-i-zer Weight Distribution System like part # EQ37141ET. If you need a higher capacity, the Equal-i-zer Weight Distribution System part # EQ64FR is available but not without the shank so you would just have to swap them out.
Please note, rise/drop is measured from the ground to the top inside edge of the receiver... view full answer...
Yes, the Solera Awning Plain Idler Head Front Cover # LC289566 that you referenced is the correct cover for a Solera idler awning head like you said you have on your 2019 Heartland Pioneer RV. view full answer...
Since your axles are already below your springs the only way to lift your 2016 Heartland Pioneer is to use the Correct Track Trailer Alignment and Lift Kit item # RR23QX. This kit lowers the attachment points for your spring hangers. They are adjustable so you can get 1-1/4" or 2-1/4" of extra height. view full answer...
I like your style, golf carts make everything better, let me show you what we have below:
**Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703.
*4-Pole Hardwire Kit with Circuit Tester # 18252.
The adjustable width hitch receiver for RV's is going to be the way to go, it is completely adjustable and customizable to fit your set up. Just need to trim to fit and you can weld or bolt it in place for a solid fit.
You will also need a connection for the trailer. Use... view full answer...